Short answer: Industrial shed Vastu comes down to a few things you decide early: the roof should slope so rainwater runs off towards the north or east, heavy machines go in the south-west half of the shed, and the power substation and DG set sit in the south-east of the plot. Build the boundary higher on the south and west, avoid a cut in the north-east corner, and plan any future extension before the first column goes up.
Why a shed needs its own look
A pre-engineered shed is a big steel box on a plot, often put up in a few months. Small units in industrial areas like Peenya, Bommasandra, Jigani or Doddaballapur are frequently built this way, on plots set out in rows along estate roads. That speed is the good part. The risk is that the shed goes wherever the fabricator finds it easiest, and the utilities get added later in whatever corner is left. My factory layout Vastu guide has the full zone map for a plant. This page covers the decisions specific to a PEB or steel shed on a standard industrial plot.
Roof slope and drainage
A shed roof is huge, so in the monsoon it moves a lot of water. Ask your PEB supplier which way the main slope runs before the drawings are frozen. I prefer the roof and gutters to discharge towards the north, east or north-east, with the downpipes and rainwater pit on that side. A roof that dumps everything into the south-west corner is a fault I come across often on sheds.
With a gable roof sloping both ways, check where the downpipes end, not just the slope. Run the storm drain along the boundary so it leaves the plot from the north or east. The yard should fall gently towards the north-east too, and that is where a sump or harvesting pit belongs.
Placing machines inside the shed
Split the shed floor into a simple nine-part grid. The heaviest presses, CNC machines, moulding units and anything on a deep foundation belong in the south, south-west and west bays. Lighter assembly, inspection and packing can come forward towards the north and east. Leave the central bay as an aisle, not a machine bed; more on that middle zone is on my Brahmasthan Vastu page.
Furnaces, ovens, heat treatment and welding go in the south-east part of the shed. A process that uses a lot of water, a washing line or cooling tower, sits better towards the north or north-east, kept low.
Substation, DG set and boundary
The power substation, DG set, HT panel and diesel tank should all sit in the south-east of the plot, outside the shed if possible. On small plots the supply line often comes in at whichever corner is nearest the road pole, and the equipment lands there without much thought. If that corner is the north-east, the extra cable cost to shift it is worth paying.
For the compound, make the south and west walls taller and solid. The north and east walls can be lower, or a short wall with grill above. The main gate is best in the north or east; on a south or west road, the position along that side matters. My east-facing factory and west-facing factory guides go through gate placement.
Plot shape, cuts and corners
Industrial plots are not always clean rectangles. A road bend, a drain or a neighbour’s boundary can take a corner away. A missing north-east corner is the cut I worry about most, then a missing south-west. A plot that pushes out at the north-east is acceptable; one that pushes out at the south-west is not. Before you buy, check the plot drawing against a compass reading on site. My plot buying Vastu checklist lists what to look for, and an online Plot Vastu check costs ₹1,499 if you want me to go through the drawing with you.
Expanding the shed later
Almost every small unit grows. When you plan the first shed, leave open land on the north and east and build in the south-west first. Later bays can extend towards the north or east with a lower roof, so the old shed stays the heavier block. A new tall shed in the north-east of the plot reverses that balance, so I advise against it. A mezzanine fits better over the south or west bays. For bigger expansions, a Vastu site visit lets me check the actual levels and columns.
Frequently asked questions
Does Vastu apply to a steel PEB shed?
Yes. Vastu reads the plot and the placement of things on it, not the building material. A steel shed follows the same directions as a concrete one.
Which way should my shed roof slope?
Towards the north, east or north-east, with gutters and downpipes on that side and the storm drain leaving the plot from there.
Where should the DG set and substation go?
In the south-east of the plot. Keep heavy electrical equipment out of the north-east and the centre.
Can you check an industrial plot before I buy it?
Yes. Send the plot drawing, a compass reading at the gate and photos of the boundary. An online Plot Vastu check is ₹1,499, with the report in 48 hours.
What is the fee for a full shed or factory review?
Industrial Vastu is quoted on request, depending on the plot size and number of sheds. A site visit is also quoted on request.
Plan your shed with me
For a running unit or a new build, my industrial Vastu consultation covers the shed, yard, utilities and the owner’s chart. Fees are on the pricing page. Book a consultation, or call or WhatsApp me on +91 74838 52618, 9 AM to 8 PM, all seven days.